Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies Air Quality & Sanitizing in Cumming: What to Know First
We provide independent Abatement Technologies air quality and sanitizing services in Cumming, with most jobs scheduled within a week and completed in a single visit. A typical whole-system treatment runs between $380 and $720 depending on the configuration and what the camera finds inside the ductwork. Every job starts with a written price before any work begins, and every duct run is photographed before and after so you can see what was actually done.
This page is for Cumming homeowners who own an Abatement Technologies air filtration or purification system and need mold treatment, bacteria sanitizing, odor removal, UV light installation, or allergen reduction. We’re not affiliated with or authorized by Abatement Technologies. We work on their equipment as an independent Abatement Technologies service provider, using manufacturer-safe methods that protect your warranty while delivering documented results. If you’re ready to schedule, call us at (678) 693-5322.
How Abatement Technologies Products Fail - and How We Fix Them
- PREDATOR 750 Series - UV lamp degradation without indicator failure. The 750-series UV-C lamps often continue drawing power while output drops below effective germicidal intensity, typically around the 14-month mark in Cumming’s high-humidity summers. The control board shows green, but the lamp isn’t killing mold spores. We meter actual UV output at the plenum with a radiometer and replace only when the 254 nm reading falls below manufacturer spec, not on a calendar guess.
- HEPA-AIRE PAS2400 - seal fatigue at the filter housing gasket. The PAS2400’s positive-pressure seal design works hard in Cumming homes where pollen counts spike in April and October, cycling the blower more frequently. The silicone gasket compresses permanently after roughly three years, allowing bypass air that defeats HEPA filtration. We replace with OEM-spec gasket material and torque to Abatement Technologies’ foot-pound specification, then smoke-test the seal.
- ABATEMENT H2000i - evaporator pan microbial growth from condensate retention. The H2000i’s shallow drain pan design traps standing water when Cumming’s summer humidity pushes dew points above 72°F. The result is black algae and bacterial slime that re-contaminates the airstream after any cleaning. We treat with EPA-registered sanitizer, install a pan tablet dispenser, and verify full drainage with a borescope before closing the access panel.
- CAP600-UV - odor recurrence due to insufficient contact time. The CAP600’s compact cabinet short-changes dwell time when airflow exceeds design spec, common in Cumming’s newer two-story homes with oversized returns. The UV kills what’s directly exposed but misses biofilm deeper in the coil fins. We calculate actual CFM against coil surface area, adjust blower speed if the system allows, and supplement with foaming cleaner that penetrates where UV cannot reach.
- PORTA-AIRE PA3300 - carbon filter saturation without replacement protocol. The PA3300’s activated carbon stage adsorbs VOCs and odors until the pores fill, typically 18-24 months in homes with active construction nearby (common in Cumming’s west-side developments). Owners smell the return of odors but mistake it for a new problem. We specify the Abatement Technologies replacement carbon module by part number and document pre- and post-treatment VOC levels with a photoionization detector.
Our Abatement Technologies Air Quality & Sanitizing Process
- 1
Written estimate on arrival. We inspect the Abatement Technologies unit, identify the model and serial, and deliver a written price before touching a tool. Haven Standard Clause 1: no exceptions.
- 2
Borescope documentation. The camera goes into every accessible duct run and across the evaporator surface. Tomas Reyes put it this way: “The camera doesn’t have an opinion - it just shows you what’s in there.” You see the images before we proceed.
- 3
Component-specific treatment selection. We match the sanitizer or remediation method to the Abatement Technologies model and the actual contamination found. OEM-spec UV lamps where the original design calls for them; EPA-registered antimicrobial for biological growth; thermal fogging only for odor cases where the source is inaccessible.
- 4
Execution with protective protocols. Negative-pressure extraction during any agitation work, sealed containment for mold jobs, and full PPE per Georgia’s mold remediation guidelines. We protect your finish and your HVAC warranty by following manufacturer torque and clearance specs on reassembly.
- 5
Post-treatment verification. Second borescope pass, airflow measurement at the registers, and a written completion summary with all photos delivered electronically. The 365-Day Done Right Promise attaches in writing.
- 6
Scheduled follow-up. For UV installations and seasonal treatments, we note the lamp replacement date and contact you before degradation begins - not after failure.
BeforeAfterWhat Abatement Technologies Air Quality & Sanitizing Costs in Cumming
These are the ranges we write on estimates for Abatement Technologies systems in Cumming. The final price depends on what the camera shows and the system configuration, not on how many vents you have.
| Service | Typical Range | What Moves the Price |
|---|---|---|
| UV-C lamp replacement (PREDATOR/CAP series) | $180 - $290 | Single vs. dual-lamp cabinet; access difficulty in attic installs |
| Whole-system bacteria/mold sanitizing | $380 - $550 | Extent of coil contamination; need for pan or plenum access |
| HEPA seal restoration (PAS2400) | $240 - $360 | Gasket replacement vs. full housing reseal; filter replacement if due |
| Carbon filter replacement with VOC verification (PA3300) | $320 - $480 | Pre-treatment VOC reading; activated carbon weight required |
| Odor elimination with thermal fogging | $450 - $720 | Source accessibility; duct run count in two-story layouts |
We also install Lennox, Trane, and Carrier air quality equipment when a full replacement makes more sense than continued remediation. Bring any competitor’s written estimate for a free second opinion under Haven Standard Clause 5.
Call (678) 693-5322 for a written estimate at no charge. Estimates include the photo documentation, not a sales pitch.
Why Cumming Homeowners Call CleanRun Air Duct Cleaning Cumming for Abatement Technologies Work
We’ve been running jobs in Cumming since 2013, including enough calls in the Vickery subdivision to know that two-story return-air trunk lines there tend to hide debris the homeowner never sees. Our crew is background-checked and uniformed under Haven Standard Clause 3: Verified Crews. Every technician is identified by name before arrival.
The 365-Day Done Right Promise is a written guarantee, not a policy subject to manager approval. If the odor returns, the mold recurs, or the UV reading drops, we make it right. The documented photo record from every visit means you can verify the work yourself rather than trusting a verbal report. And because we also service Lennox, Trane, and Carrier systems, we can recommend a replacement path when your Abatement Technologies unit has reached the end of its service life without manufacturer bias.
FAQs
No, if the work is performed with manufacturer-specified methods and parts. As an independent Abatement Technologies service provider, we use OEM-equivalent or genuine replacement components and document the procedure so warranty claims remain valid. We do not drill, cut, or modify factory housings. Call (678) 693-5322 if you need the specific warranty language reviewed before scheduling.
We measure it. Our crew uses a calibrated UV-C radiometer at the lamp surface and documents the microwatt-per-square-centimeter reading on your job record. The Abatement Technologies indicator light only confirms electrical continuity, not germicidal output. If the reading falls below effective levels during our annual follow-up, we replace under the 365-Day Done Right Promise.
The filter is doing its job, but the mustiness is likely downstream. In Cumming’s climate, condensate pans and coil fins grow mold that bypasses the HEPA stage because it’s generating odor after the filter. We borescope the evaporator compartment specifically on every HEPA service call and treat what the filter cannot reach. The photo record shows you which component is actually the source.
Replace when the cost of remediation exceeds 40% of a new system’s installed price, or when the unit lacks features you now need. We service Abatement Technologies equipment without pushing replacement, and we’ll tell you directly when the math favors a new install from any brand we carry, including Lennox, Trane, or Carrier. The free second opinion applies to replacement quotes too.
UV lamps need output verification annually; HEPA and carbon filters need inspection at 12 months and replacement typically at 18-24 months in Cumming’s pollen-heavy environment. Whole-system sanitizing is event-driven, not calendar-driven. We don’t sell maintenance contracts. We’ll note your system’s status on the written completion record and contact you when the data indicates service is due, not before.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Cumming at CleanRun Air Duct Cleaning Cumming, serving Cumming and nearby areas.